More>>

KP90G parameters

KP60G parameters

KP-60G X-ray cutting special inverter

characteristics：

This system is designed for cutting tool design,upgrade is also very suitable for cutting and old machine tools thread,integrates multiple functions of wire cylinder control,high frequency control.

The wide speed range and high speed, stable performance.

In the intermittent loads,the motor speed fluctuation is small.

Strong overload capacity,180%,5 seconds.

Low noise,small vibration,long service life.

Fast dynamic response,strong anti-interference ability.

Slip frequency compensation,make the motor run at rated current,speed close to synchronous speed.

Function:

With stepless variable speed,flexible reversing,eliminate the reversing caused by mechanical vibration,improve the cutting precision of machine tool.

Save energy,compared with the traditional motor control,eliminate noise,generated reversing mechanism when the shock,greatly improve the transmission efficiency,and can save more than 30% energy.

High frequency control,in a wire cylinder reversing,can cut off output high frequency pulse power supply,reversing available after the delay output frequency.The delay time can be adjusted.

Unilateral function of cutting,cutting the workpiece single direction,improve the cutting surface finish,also can be individually adjusted high cutting speed to improve the efficiency of unilateral return,unilateral cutting.

Processing after the end of the wire cylinder operation to limit switch after about automatic shutdown.

Parameters:

Project		Instructions
Main power input	Rated voltage	Three-phase,380V/220V,50Hz/60Hz;two-phase,220V, 50Hz/60Hz
Main power input	Change value	Voltage:±20%,Voltage unbalance rate<3%;Frequency:±5%
Main power output	output voltage	Three-phase,0～380V;0～220V
	output frequency	0Hz～400Hz
	Overload capacity	150%Rated output current of 1 minutes,110% rated output current of 1 hours.
Control performance	Modulation	SVPWM Mode
	Control mode	V/F control/non speed sensor vector control method
	Given the way	Panel given, external terminal is given, the PC given
	Speed setting mode	Operation panel digital set;the simulation setting and other 13 kinds of speed setting mode.
	Speed setting accuracy	Digital set:±0.01%（－10℃～＋40℃）
	Speed setting accuracy	Simulation setting:±0.05%（25℃±10℃）
	Speed setting resolution	Digital set:0.01Hz;Simulation setting:1/1000
	control precision	PG V/F feedback control:±0.05%;（25℃±10℃）
	control range	PG V/F feedback control:1：1000
Input output control signal	reference voltage output	1 road,10V，5mA
	Control voltage output	24V，100mA
	Analog input	1 road,-10V～+10V DC，10bit+Sign bit;1 road,0～10V/0～20mA DC,10bit,JP1 motherboard jumper at the side of V/I location selection
	type commands	2 road,FWD/COM and REV/COM control command input contact terminal.
	Programmable contact input	8 way programmable,can choose the fault reset,DC brake and other 22 kinds of operation control command.
	PG signal input	X7 and X8 for A,B open collector encoder input.
	Analog signal output	2,the output voltage,output current,output analog signal frequency.
	Open collector output	2 Road,10 kinds of running state optional.The maximum output current of 50mA.
	Alarm relay output fault	1 road,contact capacity;NO：250V_AC/5A；NC：250V_AC/3A; 30V_DC/3A
Display	Four digital display (LED)	Set frequency and output frequency,output voltage and other 16 kinds of state parameters,programming menu parameters and 12 kinds of fault code.
Display	Indicator (LED)	Parameter units,motor running direction,RUN/STOP state.
Environment	Use place	Interior,not subject to direct sunlight,no dust,corrosive gas,flammable gas,oil mist,water vapor,water or salt etc.
	Altitude	Less than 1000 meters above sea level.
	Ambient temperature	-10℃～+40℃
	Humidity	20% ~ 90%RH,no dew condensation.
	Vibration	Less than 5.9 M / S (2 0.6G)
	Storage temperature	-20℃～+60℃
Structure	Protection level	IP20
Structure	Cooling method	Natural air cooling or forced air cooling

Copyright 2018 KEPU GROUP. All Rights Reserved
Address: KEPU Yinzhou industrial Zone, Yinzhou County, Ningbo, Zhejiang Province, China 315040
Tel:+86 0574 8823 3677　 Fax:+86 0574 8823 9359   E-mail:twz2005108@163.com

国产精品乱码在线观看-国产精品乱码免费一区二区-国产精品乱码高清在线观看-国产精品路线1路线2路线-视频精品一区二区三区-视频精品一区二区